Jump to content

Guide ยท Murrieta

Tankless electric hot water heater installation

An electric tankless heater needs far more power than a tank, and your electrical panel often decides whether it can go in at all. Check that before you pick a model.

Wall-mounted electric tankless unit linked by conduit to a panel, with the dedicated breaker highlighted.

An electric tankless unit heats water as it flows, with heating elements that pull a very large current, so most models need dedicated high-amp breakers and heavy wire. The plumbing is simple: two water lines. The electrical side is the hard part. Start with the broader water heater guide, then check your panel.

What extra does an electric tankless unit require compared with a tank?

Spare capacity in the main electrical panel, one or more dedicated breakers sized to the model, and matching wire are all required. A whole-house unit can pull a heavy load, often beyond other big appliances in the house, so go through the spec sheet. If the panel is full or the service is small, an electrician may have to upgrade the panel before the unit goes in.

Read the manufacturer's spec sheet for your model. It states the breaker size, wire gauge and minimum water flow. Bring it to the quote visit, because the electrician and the plumber each need it.

Water-side needs are modest: shutoff valves on the cold and hot lines, often with service ports for flushing, and a pressure relief arrangement where the maker requires it. Scale from hard water builds on elements, and third-party estimates generally rate Murrieta tap water moderately hard to hard, so ask about flushing the unit or fitting a scale filter.

With no flue, gas line or pilot involved, some owners find electric appealing. The trade-off is the electricity bill and the panel work.

Which trades do the work, and is a permit needed?

Plumbing and electrical work are separate trades. A plumber or a general contractor connects the water, while the circuit and panel usually go to an electrician holding a California contractor license. In California a contractor license is generally required at $1,000 or more in labor and materials and whenever a permit is involved, and this job will normally need a permit plus an inspection.

The City of Murrieta Building and Safety Division (951-461-6062), the City of Wildomar, or Riverside County for unincorporated areas like French Valley and Winchester issues the permits. Confirm county phone numbers before calling. Find out who is responsible for the permit, and whether the quote covers the inspection.

Replacing an existing water heater also means the work must meet current code, which can include a drain or relief arrangement and, for a tank swap, earthquake bracing. Once a tank is removed, the plumber caps or reuses the old connections, and the quote ought to state which.

If you plan to go electric to avoid gas, ask whether a gas line cap and permit are needed. Capping the old gas line is gas work and falls to a gas contractor.

Where should an electric tankless unit be mounted?

On a wall close to the electrical panel and the existing hot water lines, with clearance in front for service and no exposure to rain. Garages, utility closets and interior walls are typical. A shorter electrical run lowers the wiring cost, and a spot near the kitchen and bathrooms shortens the wait for hot water.

Front view of a wall unit with a dashed clearance zone for space above, below and in front.

Check the clearances in the manual. Many units want space above and below. They are wall-hung, so the wall must hold the weight, and the mounting must avoid anything that could block the cover.

One local note: a garage wall in a hot Murrieta summer can run warm, and the manufacturer lists the ambient temperature range. A unit in an attic is harder to service and has to meet its own rules.

Is an electric tankless heater a good fit for a Murrieta home?

It depends on the panel, the number of simultaneous showers, and your electric rates. Electric tankless units deliver endless hot water at a limited flow, so a big household running two showers and a dishwasher may exceed what one unit can heat. Smaller point-of-use units work for a single sink or bathroom.

Weigh the alternatives. A tank avoids a panel upgrade but loses heat while idle, and a gas tankless needs a larger gas line plus venting. Our pages on tank versus tankless, gas tankless installation and tankless installation cost lay out the trade-offs, and tankless repair shows what servicing involves.

No zero-NOx rule bears on your choice today, since in June 2025 the regional air board decided against amending its Rules 1111 and 1121. Fuel choice comes down to cost and panel capacity.

Which questions come before you buy?

Learn the circuit size the maker requires, whether your panel can supply it, the flow rate at your incoming water temperature, who handles each trade, and whether the quote includes the permit and inspection. Ask what the warranty requires, such as annual flushing, and whether your hard water affects it.

Get the quote in writing and itemized. The replacement guide lists points to compare.

Send a quote request that describes your panel, the location and the number of bathrooms. We pass it to local plumbing businesses, which pay this site a fee for introductions; the one that responds prices and does the work, or brings in an electrician. The home page shows other services.

Common questions

Will my panel handle an electric tankless heater?

Maybe not. Compare the unit's amp draw with spare capacity on the panel and the service rating at the meter. An electrician makes that call on site. If the panel is near its limit, a service upgrade becomes part of the project, and it should be priced separately.

How long does the install take?

A swap in a prepared location can take a few hours, while a new circuit or panel upgrade adds time and often a separate visit. Inspection scheduling is separate again. The business that quotes will give a timeline, and you should ask for it in writing.

Can I install one myself?

Plumbing and electrical work of this size generally needs a contractor and a permit in California, and wiring a high-amp circuit is hazardous. A mistake can cause a fire or void the warranty. Leave it to a contractor, and spend your effort on comparing quotes.

Must someone be at home during the work?

Yes. Have an adult on hand when the work begins and ends, since power and water will be off for a stretch. The plumber needs access to the panel, the heater location and the main shutoff. Expect several hours without hot water.

References

Last changed