Backflow means water travelling in the wrong direction through your plumbing. A backflow prevention assembly blocks it, and a periodic test shows the springs and seats inside still hold. If a notice from your water supplier arrived, or you have a sprinkler system, you are probably in the right place. For where testing sits among other rules, see permits, codes and inspections.
What does backflow prevention testing check on my property?
A tester closes the shutoffs around the assembly, hooks up a differential gauge, and reads how each check valve and relief port behaves under pressure. A pass means the one-way valves seal. A fail means a part is worn, fouled by debris or stuck. The result is written on a form and, in most districts, sent to the water supplier.
The test is brief for a single assembly. What you notice is a short shutoff, and for a sprinkler line, a pause in watering. The tester may need to flush the line to clear grit, which is common after repairs or when irrigation pipes are old. Keep the form. If the supplier asks for it later, you will have proof.
What follows a failed test?
Normally the assembly gets new seats, springs or discs and is then retested. Replacement is needed when the body is cracked or corroded or parts are unavailable. The district may set a deadline to repair and retest. Do not remove the device, because it exists to protect the public water supply, and bypassing it can lead to penalties.
Have the tester explain what failed, and which costs less, repair or replacement. With an aging unit and scarce parts, replacing it can be the better path. A replacement or a relocation may involve a permit, and your local building office can confirm. In the City of Murrieta, Building and Safety lists 951-461-6062.
Which devices need testing, and how do I know which I have?
Look on the pipe near the meter, beside the house or in a green box by a lawn for brass or bronze hardware with test cocks (small screw valves) and a label. Common types are the reduced pressure assembly, the double check assembly, and the pressure vacuum breaker used on sprinklers. The type decides the test method.
Irrigation is the usual home case. A shed, a pond, a pool fill line, an auxiliary well, a boiler or fire sprinklers can add other cross-connection risks. A private well or any other second source of water is something to report to the water district, since mixing sources is the classic backflow danger. Rural lots in Fallbrook, Rainbow, De Luz and the Santa Rosa Plateau edge more often have wells and unusual setups, while many town lots in Murrieta and Wildomar have a meter and an irrigation assembly.
Not sure what is on your line? Photograph the label and ask the district or a plumber. Our page on how to do backflow testing shows who to ask and which building office handles permits.
What is a mobile home plumbing inspection, and does it relate?
A mobile home plumbing inspection is a review of the supply, drain, water heater and shutoffs in a manufactured home, usually requested at sale, after a repair or by a park. It is separate from backflow testing, though an irrigation backflow assembly on the lot may be reviewed in the same trip. Check with the park manager or the housing authority that covers your park.
In such an inspection the plumber checks the supply connection under the home, fittings for leaks, bracing, the water heater's relief valve, the shutoffs and any visible drains. Work beneath the home is covered in installing plumbing under a mobile home, and heaters in mobile home water heater replacement.
To have a visit arranged, ask for a price and mention the district, device type and any notice you received. The plumber home page shows what else we arrange.
Does my water district require the test, and who is my district?
Whether you need a test depends on your district's cross-connection program, and the district is the authority. Your bill names the supplier. Murrieta addresses are often Eastern Municipal Water District, while some are Western's Murrieta Division or Rancho California Water District. Wildomar is generally Elsinore Valley. Canyon Lake is mostly Elsinore Valley, with a few hundred homes on the north-east side served by Eastern.
Rainbow addresses are served by Rainbow Municipal Water District, while for Fallbrook and De Luz the supplier is generally Fallbrook Public Utility District. The City of Canyon Lake says to call and verify which district serves your street, and that is good advice anywhere the lines overlap. Check which district bills you, then ask whether your assembly is on its list and when the annual report is due.
Do not guess at a due date or fee. Districts differ, and no figure has been confirmed by us.
What does backflow tester certification mean, and can I get it online?
A tester earns a credential through a training course with hands-on practice and an exam, and water suppliers accept reports from testers they recognize. Online-only certificates are unlikely to be enough on their own because the skill is physical, using gauges on live assemblies. If you are hoping to test your own device, ask your district first, and plan on hiring someone.
The practical check for you is simpler: ask the tester which agencies accept their credential and whether they file the report. Also ask for a copy. Some districts keep a list of approved testers, and using one avoids a rejected report. A plumber who does repairs can fix a failed assembly, and the same business may test, though they are separate skills.
For commercial buildings, rules and frequency can be stricter, see commercial backflow testing, and for general service listings see backflow testing services.
Common questions
What time does a single sprinkler assembly test take?
Usually well under an hour when nothing is wrong. Failures add time for parts and a retest, and a seized or buried assembly adds time to reach it. Check if the quote includes a retest, and find out who files the form with the district.
How do I choose a tester?
Seek a credential your district accepts, working gauges calibrated on a schedule, a clear statement of whether repairs are priced separately, and a willingness to send you a copy of the report. Avoid anyone who suggests skipping the test or removing the device.
Is the test needed at a house with no sprinklers?
Often not, but your district decides. A plain home with a meter and no irrigation, pool fill, well or boiler might have nothing that needs testing. When a notice arrived, read it, and phone the district if you think it was sent in error.
Who handles the repair if the test fails?
A plumber, usually the tester or another business, replaces worn parts or the whole assembly and the assembly is tested again. Keep the old and new reports together, and send both if the district asks. Get written confirmation from the plumber of which parts were replaced and the date of the retest.
Last changed