Jump to content

Guide ยท Murrieta

Repairing a Rheem tankless heater in Murrieta

A Rheem that cuts out, flashes lights or delivers a cold stretch mid-shower can usually be traced to a short list of causes. Here is what to check, and what needs a plumber.

Tankless unit schematic: cold water enters through a screen, passes the heat exchanger and leaves past an outlet sensor.

Rheem builds tankless units in gas and electric versions, and the faults divide along those lines. Gas models trip on ignition, venting or gas supply. Electric models trip on power, elements or flow. Both suffer from scale in hard water. The wider guide to heater trouble is at water heater repair in Murrieta.

Why is my Rheem tankless heater flashing a code or shutting off?

Rheem units use flashing lights or a display code to name the fault, and the exact table is in the manual for the model on your wall. In broad terms, a code points to ignition, flame, overheating, a sensor, a vent or fan fault, or low flow. The unit locks out to protect itself and the house.

Find the model and serial plate, usually on the side or bottom. Count the flashes or read the digits, and look them up in the owner's manual or on the maker's support page for that model. Cycle the power once. If the code returns, repeating the reset does not help and may cause more failed ignitions on a gas unit.

Check first whether other things changed: a new low-flow showerhead, a clogged aerator, a closed valve after plumbing work, or a power outage. A unit that was working until a change often points straight at that change.

Why do I get a burst of cold water in the middle of a hot shower?

This is the so-called cold water sandwich. Hot water in the pipes comes first, then a gap of cold water while the unit warms up, then hot again. A short-lived burst is normal behaviour for many tankless heaters. A repeating pulse means the flow is near the unit's minimum, or a sensor or scale is interfering.

Fixes that help: open the tap a bit more to pass the minimum flow, clean aerators and showerhead screens, and clean the unit's inlet filter. Check any recirculation loop. A temperature that swings when a second fixture opens suggests the unit is undersized for peak demand, which a plumber can evaluate by fixtures and gallons a minute.

Electric units can also lose heat when the electrical supply sags or a breaker is marginal. Persistent swings are worth a call.

How does hard water damage a Rheem, and how do I flush it?

Scale coats the heat exchanger or elements, insulates the water from the heat and raises temperatures inside the unit until it trips. Third-party estimates put Murrieta tap water at about 6 to 11 grains per gallon, moderately hard to hard, and your address may differ. Your water district's yearly report gives the official figure.

Flush loop: a pump circulates descaler from a bucket through the unit between two service valves, with house valves closed.

A flush runs white vinegar or a descaler through the unit via its service valves, with a compact pump and a pair of hoses, over about 45 minutes. Yearly is a common interval in hard water. A unit without isolation valves needs them added, which a plumber can do. Clean the inlet screen at the same time and rinse the system with fresh water afterward.

If scale is a constant problem, a softener or a scale-reducing filter upstream is worth pricing. See water softener installation and whole-house softener cost.

What are the safe owner checks, gas versus electric?

For gas models, check the gas supply is open, the vent termination is clear of nests, leaves or snow-like debris, and the condensate line is not blocked. For electric models, check the breaker, and that nothing else is on the same circuit. For both, check the water valves and the inlet screen.

Do not open the cabinet of a gas unit to adjust burners or valves, and do not bypass a safety. Electric units draw a heavy current, and a hot or buzzing breaker or discolored wire at the panel means stop and call. In California, gas piping work and the wiring of a new circuit are regulated and usually need a permit.

Gas odor means everyone leaves the building at once. From outdoors, use the SoCalGas line, 1-800-427-2200, and dial 911 if anyone is at risk.

Rheem units with an app connection may also report faults to the phone; that data helps a plumber, so note the message.

What does a plumber typically repair on a Rheem?

Common repairs include igniters and flame sensors, flow and temperature sensors, fans, condensate parts, heating elements on electric units, circuit boards, and heat exchanger replacement. A plumber diagnoses first and should give you a written estimate before parts are ordered. Parts availability depends on the model age.

Ask whether the unit is still under the maker's warranty; some parts have longer cover than labor. Keep the receipt from the installation and any maintenance records, as makers often ask for them. If the repair cost comes close to buying a new unit, or the heat exchanger has failed, replacement may be the better choice, and our tankless installation cost guide and the tank versus tankless comparison help you weigh it.

Murrieta Creek Plumbing (home) arranges the visit, and the business that quotes pays a fee for the introduction. Send details through the quote request: model number, gas or electric, the code and when it began.

Ask for a written plumber quote

A few details and we'll set up a visit from a local plumber specialist, then a written quote.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who takes on your job. You pay us nothing.

Common questions

What is the service life of a Rheem tankless heater?

The Department of Energy says a well-maintained tankless heater can run for more than 20 years. Hard water shortens that if the unit is never flushed. Age matters less than history: a ten-year-old unit with yearly flushing may outlast a five-year-old one that never was.

Can a Rheem be repaired if it is under warranty?

Often yes, but the warranty may require work by a contractor and proof of maintenance, and may cover only certain parts. Read the paperwork or the maker's site for your model. Tell the plumber about the warranty before work starts so it is not voided.

Why does the unit work with one tap but not two?

Probably it is hitting its output limit, or one fixture has a clogged aerator that changes flow. A tankless unit heats a fixed number of gallons a minute, and several taps at once can exceed it. A plumber can size it against your fixtures.

Do I need to descale an electric Rheem too?

Yes, scale coats elements as well, and it causes element failure and tripped limits. Flush the same way, with the power off and the unit isolated. Electric units can also fail due to a burned element, so a plumber tests those instead of guessing.

Is a clicking sound from the unit normal?

Gas units click during ignition. Rapid, endless clicking without flame means failed ignition. Electric units may tick as elements heat. Persistent loud sounds, burning smells or smoke mean turn the unit off at the breaker or the gas valve, then call a plumber.

References

Last changed